Objectives
• Configure passwords to ensure that access to the CLI is secured.
• Configure a switch to remove http server status for security.
• Configure port security.
• Disable unused ports.
• Test security configuration by connecting unspecified hosts to secure ports.
Background / Preparation
Set up a network similar to the one in the topology diagram. The following resources are required:
• One Cisco 2960 or comparable switch
• Two Windows-based PCs, at least one with a terminal emulation program
• At least one RJ-45-to-DB-9 connector console cable
• Two straight-through Ethernet cables (PC1 and PC2 to switch)
• Access to the PC command prompt
• Access to PC network TCP/IP configuration
NOTE: Make sure that the switch has been erased and has no startup configurations. Instructions for erasing both switches and routers are provided in the Lab Manual, located on Academy Connection in the Tools section.
Step 1: Connect PC1 to the switch
a. Connect PC1 to Fast Ethernet switch port Fa0/1. Configure PC1 to use the IP address, mask, and gateway shown in the table.
b. Establish a terminal emulation session to the switch from PC1.
Step 2: Connect PC2 to the switch
a. Connect PC2 to Fast Ethernet switch port Fa0/4.
b. Configure PC2 to use the IP address, mask, and gateway shown in the table.
Step 3: Configure PC3 but do not connect
A third host is needed for this lab.
a. Configure PC3 using IP address 192.168.1.5. The subnet mask is 255.255.255.0, and the default gateway is 192.168.1.1.
b. Do not connect this PC to the switch yet. It will be used for testing security.
Step 4: Perform an initial configuration on the switch
a. Configure the hostname of the switch as Switch1.
Switch>enable
Switch#config terminal
Switch(config)#hostname Switch1
b. Set the privileged EXEC mode password to cisco.
Switch1(config)#enable password cisco
c. Set the privileged EXEC mode secret password to class.
Switch1(config)#enable secret class
d. Configure the console and virtual terminal lines to use a password and require it at login.
Switch1(config)#line console 0
Switch1(config-line)#password cisco
Switch1(config-line)#login
Switch1(config-line)#line vty 0 15
Switch1(config-line)#password cisco
Switch1(config-line)#login
Switch1(config-line)#end
e. Exit from the console session and log in again. Which password was required to enter privileged EXEC mode? Why?
Jawaban : password yang digunakan ialah CISCO, karena telah dikonfihurasi untuk menampilkan izin login.
Step 5: Configure the switch management interface on VLAN 1
a. Enter the interface configuration mode for VLAN 1.
Switch1(config)#interface vlan 1
b. Set the IP address, subnet mask, and default gateway for the management interface.
Switch1(config-if)#ip address 192.168.1.2 255.255.255.0
Switch1(config-if)#no shutdown
Switch1(config-if)#exit
Switch1(config)#ip default-gateway 192.168.1.1
Switch1(config)#end
Why does interface VLAN 1 require an IP address in this LAN?
Jawaban : karena alamat IP digunakan sebagai interface management.
What is the purpose of the default gateway?
Jawaban : tujuan dari default gateway ialah sebagai penjembatan agar jaringan local bias mengakses jaringan induk.
Step 6: Verify the management LANs settings
a. Verify that the IP address of the management interface on the switch VLAN 1 and the IP address of PC1 and PC2 are on the same local network. Use the show running-config command to check the IP address configuration of the switch.
b. Verify the interface settings on VLAN 1.
Switch1#show interface vlan 1
What is the bandwidth on this interface?
What are the VLAN states?
VLAN 1 is and line protocol is
Step 7: Disable the switch from being an http server
Turn off the feature of the switch being used as an http server.
Switch1(config)#no ip http server
Step 8: Verify connectivity
a. To verify that hosts and switch are correctly configured, ping the switch IP address from the hosts.
Were the pings successful? If the ping is not successful, verify the connections and configurations again. Check to ensure that all cables are correct and that connections are seated. Check the host and switch configurations.
b. Save the configuration.
Step 9: Record the host MAC addresses
Determine and record the Layer 2 addresses of the PC network interface cards. From the command prompt of each PC, enter ipconfig /all.
PC1 192.168.1.1
PC2 192.168.1.2
PC3 192.168.1.3
Step 10: Determine what MAC addresses the switch has learned
Determine what MAC addresses the switch has learned by using the show mac-address-table command at the privileged EXEC mode prompt.
Switch1#show mac-address-table
How many dynamic addresses are there? 3 buah
How many total MAC addresses are there? 3 buah
Do the MAC addresses match the host MAC addresses? Ya, cocok.
Step 11: View the show mac-address-table options
View the options that the show mac-address-table command has available.
Switch1(config)#show mac-address-table ?
What options are available? Untuk memutuskan , melihat nama dari PC yang mengakses.
Step 12: Set up a static MAC address
Set up a static MAC address on FastEthernet interface 0/4. Use the address that was recorded for PC2 in Step 9. The MAC address 00e0.2917.1884 is used in this example statement only.
Switch1(config)#mac-address-table static 00e0.2917.1884 vlan 1
interface fastethernet 0/4
Step 13: Verify the results
a. Verify the MAC address table entries.
Switch1#show mac-address-table
How many dynamic MAC addresses are there now? 3 buah
How many static MAC addresses are there now? 3 buah
b. Remove the static entry from the MAC Address Table.
Switch1(config)#no mac-address-table static 00e0.2917.1884 vlan 1
interface fastethernet 0/4
Step 20: Reflection
a. Why would port security be enabled on a switch?
Jawaban : agar ketika mengakses jaringan hanya no Mac address ayng terdaftar yang bisa mengakses.
b. Why should unused ports on a switch be disabled?
Jawaban : agar ports yagn tidak terpakai tidak mengganggu dan menyebabkan data terkirim ke port yang dipakai. Dan otomatis jika semakin sedikit port semakin cepat koneksi yang diperoleh.
0 komentar:
Posting Komentar